News Center

Specializing in the production of metal mesh belt/high temperature mesh belt/heat treatment welding tooling (heat treatment jig) manufacturers.

How to deal with the common problems of the Great Wall mesh belt?

How to deal with the common problems of the Great Wall mesh belt? In case of abnormal noise, electrification of the shell, tripping of the switch, serious heating of the motor and failure to start, the motor shall be shut down immediately for inspection. In order to ensure safety, the Great Wall mesh belt shall not be maintained during work. After maintenance, a trial operation of about five minutes should be carried out, and the machine should be turned on after confirming that there is no abnormality. According to the application environment conditions, the bearing grease is not regularly supplemented or replaced. In order to ensure the good flatness of the Great Wall mesh belt in the working process, the number of oil injection shall not be less than 1000 hours/time. Close the bearing and the motor bearing and fill 2/3 of the inner and outer rings of the bearing with zl-3 lithium-based smooth grease. Oil-free work is strictly prohibited. The above content by the network with manufacturers to organize the release, reproduced please indicate!

2022

03-16

Mesh belt conveyor has those maintenance details?

Mesh belt conveyor has those maintenance details? 1. The mesh belt conveyor shall be attended by personnel during operation. If the attendant usually knows and has a better understanding of the work of the conveyor. 2, the company should prepare the conveyor "equipment protection, maintenance and operation procedures", for the personnel on duty to comply. If the watchman wants to take over. 3. The feeding of the mesh belt conveyor should be uniform, and the feeding funnel should not overflow due to excessive feeding. 4. During the operation of the conveyor, the personnel on duty shall not approach the machine; the personnel shall not touch the rotating parts. If there is a defect, continuous work shall be carried out immediately to eliminate the defect. Defects affecting operation that are not easy to eliminate immediately shall be recorded and eliminated during repair. 5. When protecting the conveyor, check the operation of each component, check the connecting bolts everywhere, and tighten them in time if they are loose. However, when preventing the operation of the conveyor, the working parts of the conveyor should be cleaned and repaired. 6. The spiral tensioning device of the tail device is properly adjusted to maintain the tension of the conveyor belt. The personnel on duty shall inquire about the operation of the conveyor belt. For those damaged places, you should choose whether to replace them immediately or when they need to be repaired according to the degree of damage (whether it affects production). The removed conveyor belt should be replaced according to the degree of wear. 7. When protecting the belt conveyor, check its operating condition, clean and smooth, and check and adjust the spiral tensioning equipment. 8. When the mesh belt conveyor is connected, it should be started with load and run continuously after unloading. 9. In addition to keeping the conveyor stable and replacing a single damaged part during transportation, the conveyor shall be repaired every 6 months. When repairing, eliminate the defects in transportation and record them, remove and replace the damaged waste parts, and replace the smooth oil. The above content by the network with manufacturers to organize the release, reproduced please indicate!

2022

03-11

B mesh belt is how to work effectively?

B mesh belt is how to work effectively? 1. During the operation of B- type mesh belt, ensure that the main conveyor belt is not maintained. 2. After officially starting the conveyor, check the tightness of the chain to see if there are scrapers, jumps, tilts, missing connecting rings, missing scrapers, etc. Timely reporting and handling. 3. When it is found that the front and rear conveyor belts drive the B belt to stop or the rear sends a stop signal, stop immediately, and prohibit long-term no-load work. 4. Due to excessive load, the conveyor cannot take up the B- type mesh belt, and it is necessary to stop in time. The continuous start-up time shall not exceed 3 times, and each start-up time shall not exceed 15 seconds. 5. When starting, pay attention to whether the sound of the motor and reducer is normal and violent, whether the temperature of the motor reducer, coupling, and spindle is overheated, and whether the B- type mesh belt of the conveyor is stable. 6. The goods near the nose should be sorted out regularly to avoid burying the motor and affecting heat dissipation and normal transportation. 7. Pay attention to the transportation of goods at work, and take them out in time after discovery to prevent the transportation of goods from affecting production. The above content by the network with manufacturers to organize the release, reproduced please indicate!

2022

02-10

What are the common causes of stainless steel mesh belt slipping?

2022

01-25

Basic adjustment method of metal mesh belt

2022

01-19

Stainless steel mesh belt conveyor rust have those reasons?

2022

01-14

What are the daily problems of mesh belt conveyor?

2022

01-05

Can you tell me what problems should be paid attention to in the customization of stainless steel mesh belt?

2021

12-29

Spiral mesh belt common specifications

2021

12-21

How to maintain stainless steel mesh belt conveyor after rust?

2021

12-14

< 1 2 3 4...8 > proceed page

Mobile website

Mobile website

Contact Us

Address: Daqiao Industrial Park, Jiangdu District, Yangzhou City
Contact: Manager Sun
Mobile:13852747372
Telephone:0514-86449272
Fax: 0514-86441970
Mailbox:jdsunw@163.com

Copyright:Yangzhou Tuoyou Network Belt Factory Power by:www.300.cn | SEO

Business License